Automotive

CD4043 DATASHEET PDF

Texas Instruments CD Latches are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Texas Instruments CD Latches. Quad R/S latch with 3-state outputs. Rev. 11 — 24 March Product data sheet. Table 1. Ordering information. All types operate from °C to +85 °C. CD datasheet, CD circuit, CD data sheet: FAIRCHILD – Quad 3- STATE NOR R/S Latches. Quad 3-STATE NAND R/S Latches,alldatasheet.

Author: Kabar Mazukinos
Country: India
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 11 February 2016
Pages: 222
PDF File Size: 10.31 Mb
ePub File Size: 8.65 Mb
ISBN: 645-8-68197-252-6
Downloads: 10780
Price: Free* [*Free Regsitration Required]
Uploader: Akijora

Datasheets search archive of electronic components datasheets

LED selection indicators controlled by multiple switches Reply to Thread. Dec 8, 1. Dec 8, 45 0. Happened on this board while searching the internet with no luck. I was looking on Mouser to see what was available. Looked at quad switch ICs but those seem to be like independent switches where you can have more than one on at a time.

Any help is appreciated. Dec 10, 2. Jan 4, 65 2. You can use RS flip flop or D flip flop to make a circuit for the requirement. Attached is the datashewt for your reference.

Please note I’ve never tested it, yet I think it will work. You can test it using a breadboard. If you find the switch bounce affects the circuit performance, you can add a capacitor of nF 0. Dec 10, 3. Thanks for your input! When it comes to this IC stuff, I have absulutely no experience in this stuff but I always like to learn. I can seem to find specifics on that.

I see datashee you are using the output of Dahasheet to reset the others and diodes to control signal flow. Just out of curiosity, would it be possible to do the same thing by running that reset signal from the SW1 instead of Q?

Basically just have a short signal to trigger the reset instead of a continuous high signal as would be from the LED output. Thanks again for your help! Dec 10, 4. Dec 19, 2, A couple of other options for “radio buttons”. Actually, the second one is pretty much the same as tkng’s. Dec 10, 5. I always believed it was easier to search from something when you know the technical term.

  CENIZAS DE IZALCO PDF

That second schematic is kinda like what tkng posted with my inquiry of having the resets run off the switches instead of the output. I will have to look at these shematics some more later.

Dec 11, 6. Dec 11, 7.

Thanks for the update. I would prefer a non-toggle action. Always have one LED on. Don’t worry about the mistake. I had no clue the other way wouldn’t work. I’m still trying to get used to those truth tables.

You guys are the experts here! So moving those diodes and disconnecting the D and barQ will make it pretty much the same as Ken’s diagram if I’m not mistaken aside from the output transistors. I might stick with the because it uses only one IC chip. Dec 15, 8. Thanks for all your help so far sorry for the long winded thesis below Finally got more specifics on the circuit I’m modding.

Since it is regulated and is what the rest of the components run off, I was going to use the 3. Below is part of the circuit with the switches. I think around 2. ON part of the switch is not used but has Vo I could split the poles having 2 isolated switches and connect per original idea.

CD Datasheet PDF Fairchild Semiconductor –

I remember seeing info in the CD datasheet on the CD? Dec 15, 9. Dec 15, Dec 16, I see a small error from moving parts around. C6 goes from the IC datasgeet to ground. The switch should be connected directly to the IC1 out line and not ground. I will fix that tonight.

LED selection indicators controlled by multiple switches

Once you correct that, can you go through exactly what the circuit is supposed to do? R3 was moved to the right just to clear up some clutter.

  EL GRAN GRIMORIO DEL PAPA HONORIO PDF

The main use is for channel switching I say main becuase when the amp is in manual mode, the buttons control other things but this mod is for channel indicators It is connected via a TRS plug basic 3-connductor stereo plug S1 switch is for changing the bank Red or Green LED and the CH is for the different channels the amp can store 4 channels per each of the two banks Changes the voltage of the signal line S 3.

Dec 17, I think I will have to stick with that option for now.

Thanks a ton for everyone’s help!! I will let you know how it turns out once I can get someone to test it. Jan 7, Just wanted to update on this project. It is dqtasheet least I can do for all the help. Got some parts in today to test and a new solderless breadboard I have wanted to get one for years.

I’ll do a little testing to measure current draw and should be ready for the datashee. Many thanks to the both of you for your help!

One thing I did find is that with 3. I thought the IC could handle 10mA. Multiple LEDs each controlled by a button Posted by hbim in forum: LED Indicators Posted by opalloyd in forum: Switches controlled by MCU Posted by drevilz in forum: Led light controlled by dmx Posted by charles01 in forum: Embedded Systems and Microcontrollers.

You May Also Like: With all these invisible radio frequencies flying through the air, we should know a little bit about what exactly they are! Your name or email address: Do you already have an account? No, create an account now. Yes, my password is: Quote of the day.