Model APSC. Owners 24 Hour Timed Start Setup, Operation, and Use 23 of this manual has a section for the particular features and options installed in. Save this Book to Read prestige apsc installation manual PDF eBook at our Online Library. Get prestige apsc installation manual PDF. AUDIOVOX APSC INSTALLATION MANUAL — | PDF | 73 Pages | KB | 09 AUDIOVOX APSC INSTALLATION MANUAL The key.
|Published (Last):||8 July 2009|
|PDF File Size:||10.58 Mb|
|ePub File Size:||19.49 Mb|
|Price:||Free* [*Free Regsitration Required]|
Avoid mounting components or routing wires near hot surfaces or near moving parts like the steering wheel as it may prevent proper operation of the vehicle. PART Select a mounting location inside the passenger compartment up behind the dashboard. The mounting location selected must be within 24″ Failure to connect this wire to the ignition switch side of the of the neutral safety switch can result in personal injury and property damage.
If this wire is not used or you have difficulty accessing the glow plug preheat circuit, you may elect to utilize the Diesel timed output as specified in Remote Start feature selection 9.
Parking Light Flasher Output This wire is the normally open contact of the on board parking light flash relay.
Platinum APS-997C Installation Manual
Connect this wire to the vehicle’s parking light feed wire. Route this wire through a grommet in the firewall to the siren location. Ground Output While Running – mA This wire provides a mA ground output that becomes active 3 seconds before the Remote Start Unit initializes and remains grounded while running plus an additional 4 seconds after the Remote Start Unit turns off.
This is a normally opened starter cut arrangement, instzllation power is removed from the secu- rity system, the starter disable feature will remain operational, and the vehicle will not start. Parking Light Flasher Input This wire is the common contact of the on board parking light flasher relay. If the vehicle’s parking lights are ground switched, connect this wire to chassis ground.
Connect the Red wire intsallation the low current 12 volt signal wire from the factory door unlock switch to the factory door unlock relay.
Prestige APS-997C Installation Manual
These applications require the use of additional components which may include relays, fixed resistors, or for convenience, a Door Lock Interface.
Connector Port The 4 pin port located on the side of this module is for proprietary Audiovox data bus interface modules. These modules are used to access a variety of features in the vehicle which can be as simple as door trigger inputs, to more complex door locks outputs, or transponder interfaces for remote starting. Amnual The Vehicle’s Engine: Program Feature 5 Bank 3 There are 4 ways that the remote start monitors the engine running, one or the other must be selected for your application for the remote start to operate correctly.
The unit will monitor the voltage unstallation of the battery during remote start, wait for the voltage to drop while cranking, then look for the voltage level to go above the level it was before the vehicle began to crank which indicates the vehicle is running. The following procedure must be performed after the installation of any Remote Start Device. Mechanical Neutral Start Switch from manhal in gear.
The following two circuits may be used only if the above circuit is not available. To connect to the key in sensor circuit as shown for method 2: To decrease sensitivity, turn the adjustment screw counter clockwise.
After you have confirmed the operation of the Audiovox Remote Start unit and tested all the safety features of the system: Be certain that the chosen mounting location will not inhibit any of the controls of the vehicle.
The transmitters are pre-programmed from the factory, If you find you need to program new or additional transmitters follow the instructions below. You can enter Bank 3 from Bank 2 by turning the ignition key off then on after you’ve made the changes you wanted in Bank 2, Siren two Long ChirpYou can also go right to bank 3 by: For technical support go to www.
Page of 32 Go.
Installation Of The Major Components. Temperature Start Programming And Information. Multi Coil Adaptor Optional Information. Manual Override Safety Testing and Operation.
Aps c Installation Manual
Programming Remote Start Feature Bank 3. Add to my manuals Add.
Page 7 when used and the neutral safety switch as shown in the following diagram. Page 10 12 White Wire: Page 11 ground trigger output wire of motion detectors, microwave detectors, or glass break detectors, can be connected to this Light Green trigger input wire.
Page 12 21 Light Blue Wire: Page 16 These applications require the use of additional components which may include relays, fixed resistors, or for convenience, a Door Lock Interface. Page 18 Connector Port Installagion 4 pin port located on the side of this module is for proprietary Audiovox data bus interface modules.
Page 19 Monitoring The Vehicle’s Engine: Page 22 Mechanical Neutral Start Switch from starting in gear.
PRESTIGE APSC INSTALLATION MANUAL Pdf Download.
Page 24 To connect to the key in sensor circuit as shown for method 2: Page 25 Installatioh decrease sensitivity, turn the adjustment screw counter clockwise. Page 26 The transmitters are pre-programmed from the factory, If you find you need to program new or additional transmitters follow the instructions below.
Amnual 27 b 27 of Page 29 b 29 of Page 30 For technical support go to www. Comments to this Manuals Your Name. Enter text from picture: By pressing ‘print’ button you will print only current page.
To print the manual completely, please, download it. Don’t show me this message again. Got it, continue to print. Don’t have an account?