Manuals and User Guides for Panasonic AG-HPX We have 4 Panasonic AG- HPX manuals available for free PDF download: Service Manual, Operating. View and Download Panasonic AG-HPX service manual online. Memory Card Camera-Recorder. AG-HPX Camcorder pdf manual download. Also for: . If the unit is being used in the MANUAL mode or AUTO mode, set the AGC item on the AUTO SW screen of the setting menu to OFF to use this function. ○TEXT.
|Published (Last):||15 August 2018|
|PDF File Size:||20.96 Mb|
|ePub File Size:||19.6 Mb|
|Price:||Free* [*Free Regsitration Required]|
WARNING This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. When servicing, observe the original lead dress. If a Some semiconductor solid state devices can be damaged short circuit is found, replace all parts, which have been easily by static electricity.
Such components commonly are over-heated or damaged by the short circuit. Setting and confirmation of Date and Time of internal clock The lithium battery is a critical component.
It must never be subjected to excessive heat of discharge. It must therefore only be fitted in equipment designed specifically for its use. Replacement batteries must be of the same type and manufacture. These items are for factory use only. The following screen is displayed.
Ag-hpx050 switches over when press the cursor Left and Right button. In the following cases, please execute the DATA initialization. These are not required for update. Do not power down or pull card while upgrading.
Panasonic AG-HPX500 Operating Instructions Manual
If the program quits during loading, the data will be erased or part writing condition and the restart is not made. However software can not be update, please contact Panasonic Service Engineering. When shifting to the update qg-hpx500 of the flash and microcomputer, following screen is displayed. The name of firmware in the update is displayed. The progress can be confirmed by progress bar. If the update is not successful, an error message will appear as follows.
When the power supply is shut off on the way of updating, or when updating does not start, or when the above error occurs, turn the power OFF and ON.
Panasonic AG-HPX500 user manual
Then perform writing again. PC EVR software Measuring board VFK Extension cable Unscrew a screw A with nut on Measuring Board as shown in figure Supply power to the Camera-Recorder and turn power ON. The following screen will appear. Clock information on the camera recorder is not cleared.
Setting of Recording format and system A setup of a recording format can be performed in the column of RecFormat. Please confirm that mark is corresponding to the msnual of the camera recorder.
Green is displayed to the status lamp while reading it. The following message is displayed when saving a file is completed.
This camera recorder is set to CAM mode. Because the EVR software can be written data at a time only by as many as 1 piece of IC, it is necessary to write three files. Red is displayed to the status lamp while writing it. When the last 8 figure numbers are noted in advance, input the same numbers as noted ones. If the last 8 figures are missed, new numbers are given. So please contact the Panasonic Service Engineering. Factory Initialize Please note that the following data etc. Operation after major part exchanged Operation List These are items that must be done when the major part has been changed.
Operation flow chart after major parts exchanged Be careful the hour meter information can not be backup, restore and writing operation. If necessary, save the LOG data. Confirm that the CAC files saved on the camera recorder. If the numbers are missed, so please contact the Panasonic Service Engineering.
Write the Serial Number. Load the backup data to new board. If writing is necessary, please contact Panasonic Service Engineering. Moreover, the CAC data file and the added CAC data file at the time of factory shipments are downloadable on the support page of the following website.
Please return a CAC file to the state before board exchange. Disconnect the connector A and B as shown in mznual Unscrew the 4 screws A as shown in figure Disconnect a connector A as shown in figure Screen explanation of adjustment software Preparation of adjustment When performing the electrical adjustment, the Camera Adjustment software is used. Adjustment item Below indicated tools are required to perform each adjustment in addition to tools in introduced in item Screen explanation of adjustment software Setup of EVR ag-hx500 for camera adjustment 1.
The Camera Adjustment screen is displayed. D-Terminal Output Level adjustment 1. Confirm that the camera recorder set to NTSC mode. Video Terminal Output Level Adjustment 1. Shoot the grayscale chart so that fit aghpx500 picture manaul the frame of grayscale chart.
When the power of camera recorder is becomes turned on, the following screen is displayed. Shoot the white chart so that the full screen is white. When replacing any of these components, use only the same type.
Components identified with the mark have the special characteristics for safety. You can initialize them separately. Item Description of settings Items in bold are factory settings.
Panasonic AG-HPX user manual – – Solve your problem
Selects the gamma curves other than the news gamma curve. This gamma setting is suitable for HD shooting. Makes a mellow image using the gamma curve which has a gentle incline in lowbrightness curve.
Selects the recording format for P2 card. Selects the function of the F. Selects D or SDI connector. Selects external DC power supply type.
This problem can be confirmed by only Personal Computer. Page of Go. Page 38 – Display operation of a Service menu and Page 51 Page 52 – Factory Initialize Page 53 – Operation after major parts exchanged Page 54 – Operation flow chart manhal major parts e When servicing the viewfinder.
Unauthorized copying and distribution is a violation of law. Table of Contents Add to my manuals Add. Page 6 Read this first!
Software Version Display Service Menu gui mnual. Pc Evr Software 6. Setup Of Pc Evr Software Setting Tool Screen Write Uid Screen Save And Write Eeprom Data 7. Save Data Of Sys-eeprom Write Data Of Sys Eeprom Uid Writing Procedure 4. Operation After Major Parts Exchanged